Connectors

../../../../_images/servo_node_connect_d3_e1.png

Before attaching cables, please check these guidelines:

Wiring instructions

Power Terminal

../../../../_images/SOMANET_Drive_1000_D3_Power.png
Terminal #  
1 Phase A
2 Phase B
3 Phase C
4 Phase D
5 Ground
6 Main Power Supply 12-48 V *
7 Optional Logic Ground
8 Optional Logic Supply 12-24 V (20 W max)**

* To be run with an appropriate extra-low voltage supply without contactors behind the power supply. Further information can be found here

** not connected by default. Upon request only, please contact sales@synapticon.com

Grounding and attaching power and brake cables

Encoder Port 1

../../../../_images/SOMANET_Drive_1000_D3_Port_1.png
Pin # ABI/ABZ (RS422) ABI/ABZ (TTL)* HALL (TTL)** BiSS (RS422) SSI (RS422)
1 MA- Clock-
2 5 V *** 5 V *** 5 V *** 5 V *** 5 V ***
3 Ground Ground Ground Ground Ground
4 MA+ Clock+
5 A- A W (C) SLO- Data-
6 A+ SLO+ Data+
7 B- B V (B)
8 B+
9 I- I U (A)
10 I+

* To use ABI/ABZ with TTL please ensure that your Encoder is capable to sink 5 mA to GND when the output of the encoder is 0

Attention

** Our upcoming version Drive 400/1000/2000 E1 will support Half-Duplex communication on this connector instead of HALL. To ensure your configuration will work with future versions of this drive, please use connector 2 instead for current development.

*** This is a 5 V supply that can provide up to 250 mA for external use.

The supply is protected against short to ground and keeps the current below 400 mA in a continuous short.

Encoder Port 2

../../../../_images/SOMANET_Drive_1000_D3_Port_2.png
Pin # ABI/ABZ (RS422) ABI/ABZ (TTL)* HALL (TTL) BiSS (RS422) SSI (RS422)
1 MA- Clock-
2 5 V ** 5 V ** 5 V ** 5 V ** 5 V **
3 Ground Ground Ground Ground Ground
4 MA+ Clock+
5 A- A W (C) SLO- Data-
6 A+ SLO+ Data+
7 B- B V (B)
8 B+
9 I- I U (A)
10 I+

* To use ABI/ABZ with TTL please ensure that your Encoder is capable to sink 5 mA to GND when the output of the encoder is 0

** This is a 5 V supply that can provide up to 250 mA for external use.

The supply is protected against short to ground and keeps the current below 400 mA in a continuous short.

Encoder Port 3 / Digital IO

../../../../_images/SOMANET_Drive_1000_D3_Digital_IO.png
Pin # GPIO REM 14/16MT BiSS (LVTTL) SSI (LVTTL)
1 3.3 V * 3.3 V * 3.3 V * 3.3 V *
2 Digital IO 1** SS SLO Data
3 Digital IO 2** SCK MA Clock
4 Ground Ground Ground Ground
5 Digital IO 3** MISO
6 Digital IO 4** MOSI
7 5 V *** 5 V *** 5 V *** 5 V ***
8
All Digital IOs are 3.3 V LVTTL CMOS logic and can be used for data rates up to 20 Mbps.

* This is a +3.3 V supply that can provide up to 250 mA for external use.
The supply is protected against short to ground and keeps the current below 400mA in a continuous short.

** Can be configured as 5.0 V CMOS logic. Upon request only, please contact sales@synapticon.com

*** This is a +5 V supply that can provide up to 250 mA for external use.
The supply is protected against short to ground and keeps the current below 400mA in a continuous short.

Note

Each Digital IO needs to be configured as a Digital Input or Output via object 0x2210 (“GPIO”).
The object can also be used to activate a pull-down resistor.

Changes may require to powercycle the node.

Analog IN

../../../../_images/SOMANET_Drive_1000_D3_Analog_IN.png
Pin #   Default Setting *
1  
2 Analog Input 1 - Connect to Ground **
3 Analog Input 1 + Single-ended 0-10 V
4 Ground  
5 Analog Input 2 - Connect to Ground **
6 Analog Input 2 + Single-ended 0-10 V
7 5 V ***  
8 10 V ****  
9 Analog Input 3 - Differential ±5 V
10 Analog Input 3 + Differential ±5 V
11 Analog Input 4 - Differential ±5 V
12 Analog Input 4 + Differential ±5 V
* All Analog Inputs can be configured as single-ended 0-5 V, 0-10 V, 0-20 V or differential ±5 V, ±10 V independently.
Upon request only, please contact sales@synapticon.com

** Must be connected to Ground when the Analog Input is set to Single-Ended Mode.
It is recommended to use a separate ground cable for each single-ended analog signal/cable and twist or tie them together.

*** This is a 5 V supply that can provide up to 100 mA for external use.
The supply is protected against short to ground and keeps the current below 400mA in a continuous short.

**** This is a 10 V supply that can provide up to 25 mA for external use.
The supply is protected against short to ground and keeps the current below 100mA in a continuous short.

Error Before Calibration: 1.5%

EtherCAT port

../../../../_images/D3_Drive_1000_EtherCAT_cut_rj452.png

EtherCAT IN Port

Pin-out
Pin Name Type Function
1 * TX+ O Differential transmit output
2 TX- O Differential transmit output
3 GND P Ground
4 RX+ I Differential receive input
5 RX- I Differential receive input

* Pin 1 is on left

EtherCAT OUT Port

Pin-out
Pin Name Type Function
1 * TX+ O Differential transmit output
2 TX- O Differential transmit output
3 GND P Ground
4 RX+ I Differential receive input
5 RX- I Differential receive input

* Pin 1 is on left

Connector types and mating parts numbers

Connector description Manufacturer Item Number Mating part Crimping Contact Cable
Analog IN JST Sales America Inc. SM12B-GHS-TB GHR-12V-S SSHL-002T-P0.2 26-30 AWG*
Encoder Ports 1 & 2 TE Connectivity 1-338068-0 1-215083-0 (remove latch!) N/A Flat Cable 28 AWG P1.27
Port 3 (Digital IO) JST Sales America Inc. SM08B-GHS-TB GHR-08V-S SSHL-002T-P0.2 26-30 AWG*
Power Terminal Block Phoenix Contact 1935831 N/A   5859 WH005 (Alpha Wire)
EtherCAT IN/OUT Molex 53261-0571 510210500 ** 500588000 28-32 AWG
* Crimped cable from JST Sales America can be used, Parts number: AGHGH28K305

** Housing only. Complete cable assemblies in various lenght also available, for example 151340501 (50 mm)